Mitsubishi i (ha1w) service manual




mitsubishi i (ha1w) service manual

Содержание статьи:
  • Фото
  • Mitsubishi i-MiEV (HA3W) Service Manual - коллектив скачать бесплатно без регистрации pdf
  • Видео
  • Похожие статьи
  • Сервисная документация по техническому обслуживанию и ремонту электромобиля Mitsubishi i-MiEV.

    Mitsubishi i-MiEV (HA3W) Service manual Руководство по ремонту для станций технического обслуживания содержит: подробное руководство по техническому обслуживанию (включая электросхемы) и ремонту автомобиля Митсубиси.

    ФАКТ! Компания Mitsubishi Group создана в Японии, в далеком 1870-м году. И с тех пор она ни разу не меняла свой логотип. Три известных ромба символизируют три бриллианта, «трех китов», на которых держится вся концепция концерна: честность, ответственность и готовность к сотрудничеству.

    Мицубиси _model_.  Запчасти на Mitsubishi i в кузове HA1W. Выберите комплектацию.

    mitsubishi i (ha1w) service manual

    mitsubishi i (ha1w) service manual

    In order to enable the leakage detection, the following settings are req uired to let the unit memorize the initial condition initial refregerant amount. Как выяснить причину и устранить. Авторевю, Автоцентр, Автомир, Top Gear , За рулем, Тюнинг автомобилей, 4x4 Club, Офф-роуд драйв, Redline, Автомобили, АВТО панорама, Клаксон, Автогид, NEW Auto, Quattroruote, АвтоЗвук, 5 колесо, Полный привод 4х4, Автопилот и другие. How to start "Judgment of refrigerant leakage " mode.

    mitsubishi i (ha1w) service manual

    mitsubishi i (ha1w) service manual

    mitsubishi i (ha1w) service manual

    mitsubishi i (ha1w) service manual

    mitsubishi i (ha1w) service manual

    Mitsubishi i-MiEV (HA3W) Руководство по ремонту для станций технического обслуживания » Автолитература. Руководства по ремонту и эксплуатации автомобилей

    UK S erv i ce Ref. W h en p ump ing down th e refrigerant, stop th e c omp ressor b efore disc onnec ting th e refrigerant p ip es. C h ec k th e error status, stop th e op eration, and c onsult y our dealer.



    Error information Error code Error unit Function setting Check Self check Check menu Error history Refrigerant volume check W h en a P rob lem O c c urs D uring O p eration If a problem occurs in the air conditioner, the indoor and outdoor units will stop, and the problem is shown in the remote controller display. When the error history is reset, the display will look like the one shown below.

    mitsubishi i (ha1w) service manual

    Press the button twice within 3 seconds. Refer to the following tables for details on the check codes. Symptom Cause Wired remote controller S y mp toms: LED display of the indoor controller board S y mp toms: N oth ing is disp lay ed on th e remote c ontroller. Inspection method and Diagnosis flow Cause troubleshooting Check the voltage between S1 and S2 on the terminal block TB 4 of the indoor unit which is used to connect the indoor Inspection method and Diagnosis flow Cause troubleshooting Check the voltage between S1 and S2 on the terminal block TB 4 of the indoor unit which is used to connect the indoor unit and the outdoor unit.

    F req uent c alling from c ustomers Phone Calls From Customers How to Respond Note 1 The operating display of remote 1 Check if power is supplied to air conditioner. Unit does not operate controller does not come on. Nothing appears on the display unless power is at all. Phone Calls From Customers How to Respond Note 1 Check the set temperature of remote controller. The room cannot be cooled or heated sufficiently. The outdoor unit cannot be operated if the set temperature is not appropriate.

    mitsubishi i (ha1w) service manual

    The outdoor unit operates in the following modes. When the set temperature is lower than the room temperature.

    Phone Calls From Customers How to Respond Note Something 3 Air blows out for a while after However, this control is also 3 This is not a malfunction. The blower is operating just for cooling down the applied to the models which with the heated-up air conditioner. Phone Calls From Customers How to Respond Note A white mist is ex pelled from the indoor unit. This is not a malfunction. This may occur when the operation gets started in the room of high humidity.

    Water or moisture is ex pelled from the outdoor COOL: Pay attention to the service. M edium temp erature th ermistor " " " " I ntake temp erature T H1 S witc h F unc tion E ffec tiv e timing S witc h No function — — — Power failure Auto recovery No auto recovery When power supply ON Display Compressor operating freq uency control I ni ti al setti ng Functi on S etti ng s Initial setting Factory setting -: Not available Mode Setting 4-Way Ceiling Function Settings Wall mounted cassette concealed PLA-B A 2 3 PEAD-JA Q PKA-FAL 2 PKA-HAL PKA-KAL Filter sign h h No filter sign indicator Q uiet Air flow Refer to the Fan speed Standard Function setting Check Self check Function setting Ref.

    mitsubishi i (ha1w) service manual

    In this section, an ex ample of setting the room temperature detection position is given. If settings for a mode are changed by function selection, the functions of that mode will be changed accordingly.

    Check all the current settings according to steps 2 to 7 , fill in the "Check" S elec ting func tions using th e wireless remote c ontroller T y p e C [ F low of func tion selec tion p roc edure] F low of func tion selec tion p roc edure The flow of the function selection procedure is shown below. L ossnay High p ower T imer W eekly timer L ossnay U se to set th e v ane angle.

    How to Change Front and rear Brake Pads and Rotors (Complete Guide)



    • Подписаться по RSSRSS подписка
    • Поделиться VkontakteПоделиться Vkontakte
    • Поделиться на FacebookПоделиться на Facebook
    • Твитнуть!Твитнуть

    Оставить комментарий

    Return to Top ▲НА ВЕРХ ▲